Brief analysis of four issues to be considered in uv plastic printing

UV ink printing or UV glazing on the surface of plastic substrates is becoming more and more popular, and this is a challenging task. Plastic printing materials have been used in the printing industry for decades. With the popularity of UV inks and varnishes, UV ink printing on plastic substrates has raised new issues for printing plants and ink manufacturers. The biggest question is how Make the UV ink / varnish firmly adhere to the surface of the plastic substrate, that is, the problem of adhesion.

1. Surface tension of plastic substrate

When printing plastics, the surface tension of the plastic substrate is the first factor to be considered first. Many plastic films have a low surface tension before being processed, and generally need to be surface-treated to increase the surface tension of the plastic substrate. After processing, they generally reach 40 dynes / cm or higher. Usually, plastic substrate suppliers have treated the surface of the plastic, but the processing effect will soon be lost.

For printing houses, online processing is the best solution to ensure that the surface tension of the plastic substrate during printing remains within an acceptable range. Corona discharge (oxidation) treatment is the most common treatment method. It is used in the surface treatment of various plastic films and will not damage those plastic substrates that are sensitive to temperature. Corona discharge uses high-frequency high-pressure or medium-frequency high-pressure discharge to treat the plastic surface to activate the surface and make it porous, so as to improve the adhesion of the plastic film surface to the ink and improve the printability of the film. For example, after commonly used PE (polyethylene) film undergoes corona discharge treatment, unsaturated bonds such as carboxyl group and carbonyl group are formed on the PE molecular chain. After the surface is oxidized, the PE molecules are converted into polar molecules, increasing the surface energy. Generally, the surface tension of PE is increased from 31 dynes / cm to 39-40 dynes / cm, which increases the wettability and adhesion of the PE film to UV ink / varnish, thereby improving the firmness of the imprint degree.

The flame method is more used in the surface treatment of high-temperature-resistant plastic products, which enables the plastic to remove oil stains on the surface and melt the thin layer of the surface under the action of instantaneous high temperature to improve the inking ability; also use chemical treatment, but this method is usually Used in conjunction with the corona discharge treatment method, the chemical treatment method uses an oxidizing agent to treat the surface of the polyolefin plastic to generate polar groups on the surface, so that the surface of the plastic substrate can be well wetted by UV ink / varnish adhesion . In order to detect the surface treatment effect of plastic substrates, plastic film printing manufacturers are best equipped with Dyne test pens.

After treatment of the plastic film, the surface tension of the ink is lower than that of the plastic film. Similarly, in order to make the varnish wet well on the ink surface and firmly adhere to the ink surface, the surface tension of the varnish is lower than that of the ink. Therefore, the UV ink formulation is very careful about the selection of raw materials, which is to obtain acceptable surface tension. Studies on various ink formulations have found that the surface tension of solvent-based inks is generally lower than other types of inks, so it can be spread on a variety of plastic film surfaces. Therefore, the surface treatment of plastic substrates is especially critical when printing with UV inks.

2. Expansion and permeability of plastic substrates

Unlike many commonly used printing papers and paperboards, the surface of the plastic substrate does not allow ink / varnish to penetrate the micropores inside. However, some plastic substrates will swell when they come in contact with some raw materials of UV ink / varnish. Therefore, use this feature to make plastic substrates used with certain UV inks, so that the ink / varnish can penetrate into the interior of the plastic substrate. During curing, due to the internal penetration of ink / varnish, a strong and strong adhesion effect can be formed between the ink / varnish and the surface of the plastic substrate. In addition, the workshop temperature can be increased to enhance the penetration effect between the plastic substrate and the ink / varnish, which is also one of the ways to improve the adhesion between the UV ink / varnish and the plastic film.

3. Ink glass transition temperature (Tg)

In physics, certain substances form glass when they are below or equal to the substance's "Glass Transition Temperature". Compared with ordinary inks / varnishes, the components of UV inks / varnishes generally contain materials with smaller molecular weights. These materials are thicker and more cross-linked by the ink layer formed by the reaction during curing. At the same time, the glass transition temperature (Tg) of the film layer after UV ink / varnish curing is higher and the film layer is harder, so it has good abrasion resistance and chemical resistance.

If the Tg of the film layer is higher than the working temperature in the hot stamping or laminating process, the UV film layer in the finished product will not be able to firmly adhere to the gold foil or composite plastic film. UV inks / varnishes made with low Tg materials can adhere well to gold foil and composite films in the post-press processing process. Sometimes in order to enable the bronzing or lamination to proceed smoothly, it is necessary to lower the working temperature of the process.

4. Degree of curing

For any UV ink formulation, the appropriate photoinitiator must be selected to optimize the performance of the ink layer after curing. Each UV ink / varnish formulation works with a specific, sufficient amount of UV energy. If the spectral band and power of UV energy change, it will affect the performance of the ink layer after curing.

On the surface of the plastic substrate, you may feel that the UV ink / varnish has been cured, but in fact, it is likely that the entire film layer has not been completely cured. The degree of curing close to the bottom of the film layer is critical to achieving good adhesion. The inside of the film layer and the bottom layer are not completely cured, so the penetration of UV ink / varnish inside the plastic substrate is meaningless. Once the curing energy changes, the surface tension of the film layer will also change, which ultimately affects the successful completion of the subsequent post-press processing process.

The plastic packaging market is an exciting market, and UV inks / varnishes are commonly used materials for plastic packaging printing. Fast curing means higher production efficiency, and drying ink without heat means less impact on the environment and workshop.

Adhesion is one of the few problems of UV ink / varnish in plastic packaging printing. The main reason is that printing customers constantly need new plastic substrate materials and new applications, making the adhesion of the film layer UV plastic Common problems in printing. As long as the four issues mentioned above are fully taken into account, the problem of adhesion in plastic printing can be solved.

Crochet Teether

Crochet Teether,Crochet Wooden Teether,Crochet Teether Toy,Beech Wood Teether,Baby Pacifier Chain

Dongguan UMY Garment Co., Ltd , https://www.umycn.com